Veronese Bells, Fittings and Ringing - by David Bagley.
S.Giorgio in Braida,
The oldest Veronese ring.
Bells
Until 1984, it was thought that full circle bell ringing was unique to
"English" style change ringing. In the
The method of casting bells in
The mould is made by starting with a hollow brick core, and building this up
with loam. A 'false bell' made out of a lighter material is constructed around
the core, and the wax decorations are placed on the outside of the false bell.
Decorations on an Italian bell are a very important part of the bell, and
some decorations are delicate and complex. The art-work is religious in nature,
with subjects such as the Virgin Mary, Christ on the Cross, and images of
Saints, together with more decorative borders. A plaster mould is carved, and
molten wax poured in and allowed to set. The wax is then removed from the
plaster mould and stuck to the side of the false bell. The cannons for the
false bell are also made out of wax, and are usually highly decorated.
Once the false bell is completed, then the cope is carefully formed around
it to avoid damaging the decoration. Hooks are embedded into the cope so that
it may be lifted to remove the false bell. Once finished, a charcoal fire is
lit within the hollow core, which melts out the wax and dries the mould. This
is kept lit for several days, and often a second charcoal fire is lit on top to
heat that part of the mould. Once a mould has been made, the strickle is
destroyed to preserve the uniqueness of the bell.
Bell metal is usually about 75% copper, and 25% tin but proportions vary a
little from foundry to foundry. The moulds are placed in a casting pit next to
the furnace and the molten metal at 1100oC is run off under gravity. Once cold,
the bell is removed from the pit and cleaned and polished to a very high
standard.
The whole process of making the mould and decorations, casting and cleaning
takes around 30 or 40 days, even for small bells. Only on rare occasions are
bells tuned. This is usually done with an angle grinder. If a new bell needs
tuning, then it is said that the founder has failed to cast the bell properly.
Bell
A Veronese bell and fittings.
The average tower in the
The wheel rim is made out of 'U' shaped steel channel, and is welded into a
circle. The spokes are welded to the wheel rim and the whole assembly is bolted
to the side of the headstock. Wheel stays are also used to give the wheel
rigidity. The rope is attached to the wheel with a toggle arrangement and this
is positioned at the same height as the bearings. The ground pulley is always
at least one wheel diameter directly below the rope toggle, but sometimes it is
much further away, depending upon the height of the frame.
The ropes consist of steel cable from the bell wheel to just above the
ringing chamber, where a hemp rope is spliced on. The steel cable does not
stretch even with very long rope drafts. The hemp rope is generally fairly
thick and has no sally or tail end, finishing in a heap on the floor. New hemp
ropes are boiled to remove any elasticity before being spliced onto the steel
cable.
Clapper staples are independent and not cast in to the top of the bell.
Leather baldricks are fixed to the top of the clapper and pass through the
staple which is shaped like a stirrup. The bells usually swing in and out of
the tower openings, which makes them very loud outside. Because of the danger
of a broken clapper flying out of the tower, a loop of steel cable is passed
through the flight of the clapper, and around the side of the ball. This is
then tethered at several places up the shaft and passes through the clapper
staple.
Veronese Ringing.
Although Veronese bells are hung in a very similar manner to English bells,
the ringing is quite different. Since there are no stays, the bells must be
rung up before each "concerto". There are two methods of raising the
bells, namely the fast way and slow way. When ringing up the slow way, the
treble is raised first and starts ringing slowly on its own when it is up. Then
the second is then raised and joins in ringing slow rounds. Then all the other
bells are raised in turn and join on the end of the slow rounds. When the tenor
is up, then the concerto can begin. The fast way is less interesting, and
involves all the bells ringing up as fast as they can and sorting out the
ringing into rounds when up.
When ringing a concerto, the conductor calls out the number of the bells
which are to ring. Each ringer has to hold his bell on the balance until his
number is called, when he pulls off and sets his bell at the other stroke.
On 5 bells the bells are usually numbered 1-5, but on six bells the treble
is usually number 6 (rounds being 612345). On nine bells, the numbering system
is 1-9, and on ten, the new treble is number zero. Additional bells are given
letters, not numbers. There are a few other systems of calling, but these are
not commonly used.
Concertos usually contain many chords of two or sometimes three bells.
Chords are given names, usually based on the ordinal number for the heavier
bell in the chord, for example, a chord involving 4 and 2 striking together is
called "quarte". Chords with three or more bells are usually called
as a pair of bells together with the extra bell(s), for example a chord with
8,6 and 1 could be called "octave e uno". or eighth (meaning 8 and 6)
and number one.
Concertos almost always end in a flourish of these chords, which sounds very
impressive when it is done well. Lowering the bells after a concerto is,
however, a very haphazard affair, with all the bells just running down
randomly. Often, once the concerto is finished, the ringers will simply pull
their bells off and walk out of the tower!
Some bands are beginning to lower in peal, which is something they have
picked up from visits to the
Every 'concerto' is thought of as a public performance, and is often treated
with applause at the end. The standard of the striking is, as a result, usually
very high. It is usual for a ringer to only ring with his or her own band. It
is very rare for any one ringer to visit other towers on their own. Tower
'grabbing' is almost unheard of as a result. I have experienced a 'knock and
grab' when the band taking us around stopped at a village for a drink at the
bar, and the priest was persuaded to open up the tower!
The one time at which ringers do get to ring on other bells is at a
competition. Many bands go into competition ringing in a big way, and the good
ones win many trophies. The 1988 young ringers' competition at Sprea (5 bells,
10cwt) had 21 teams taking part! Each competition will have a special concerto
composed for it, and a new trophy will be made. Each team must ring this
concerto, and the system of marking is complex. Different types of faults gain
different penalty points. If the concerto is miscalled, or if a bell turns
right over, then this leads to disqualification. Large variations in rhythm
lose more points than small ones.
Many of the ringers are affiliated to the "Associazone Suonatori di
Campane a Systema Veronese" (ASCSV). This is in turn part of a national
organisation called ANBIMA which represents many different forms of music,
including marching bands. The ASCSV is run like any other guild or association
with a monthly newsletter, and many other events.
If you wish to visit
Please note that this email address has been protected to avoid
abuse by spammers. You will need a JavaScript-enabled browser.
Information, facts and figures.
There are about 300 ringing towers in northern
Weights of bells are given in 'quintali' which are multiples of 100Kg. A
bell is considered to be a musical instrument, so the note is of greater
importance than the weight. It is strange that the bells are not tuned
(harmonically or otherwise) as most other musical instruments are.
Verona Cathedral has nine bells, tenor 88cwt (in
Ab) and is the largest full circle ringing bell in the world. The bells were
originally cast in 1931 by the Cavadini foundry of
S. Elena in
Most towers have diatonic scales of 5, 6 or 9 bells. A few have more than 9,
and some have semitones. Breganze near to the city of
The
The
The Capanni foundry has built a mobile tower consisting of a ring of 6,
tenor about 6 cwt, and the tower is small enough to be lifted onto the back of
a lorry. It usually travels around the
For those with a broadband connection, there is also a good video clip
downloadable from here.
There is some more excellent video of Veronese ringing at this page although the
last few seconds are of actually not Veronese ringing, but a similar system in
the
YouTube has loads of Veronese clips with more being added all the time. Start here for several excellent clips, even one of Verona Cathedral ringing.
David Bagley